Zar Formenti S.R.L.

Loc. Vigna della Pace, 2/2, 20086 Motta Visconti (MI)
Italy

Telephone +39 02 90000788
Fax +39 02 90001850
info@zar-formenti.com

Location

Hall map

boot 2017 hall map (Hall 9): stand B04

Fairground map

boot 2017 fairground map: Hall 9

Our range of products

Product categories

Our products

Product category: Inflatable Boats

ZAR 43

It is the “little one” of the family. But maybe the most amazing one.
ZAR 43 is 4.30 meters long and 2.16 meters wide; it offers liveability, safety, comfort and performances that are hard to see in a traditional 5.5-meter long rubber dinghy.
Even if mathematicians don’t like it (but as you well know sometimes math can be an opinion), it has been able to show that 4.50 can be equal to 5.50. Absolutely safe and comfortable transportation of 7 persons, with huge peaks, it can bear a 90 HP and it sails fast and slender like a squirrel with a motor “without a licence”.
It has two separate sun bathing beds (the front one is almost as big as a double bed), it has a fuel capacity of about 100 litres and a water capacity of about 60 litres without taking away any passenger space.
Just like its bigger brothers, it has tubulars with 6 compartments and it can be provided with a roll bar, shower, awnings and tents for nautical camping.
ZAR 43 does not have any competitor simply because it is a ZAR, a little gigantic ZAR.

More Less

Product category: Inflatable Boats

ZAR 65

The ZAR 65 is big, spacious and comfortable: a real fl agship!
It is the best interpretation of the philosophy that gave birth to the ZAR dynasty.
Places and volumes at will without any waste. Everything is functional, thought and built with precise goals.
The eight/nine forward running seats was been conceived to give the maximum possible comfort; the seats are made according with the best ergonomic modern studies like in the most prestigious limousines. Born for the comfort and to enjoy the navigation and the open air life, the ZAR 65 is also able to give special performances emotions to all its lucky owners.
The ZAR 65 is fast and safe, soft on the waves, manageable and nimble also in the worst see conditions, because of a very deep and long hull, unthinkable in a 6,5 mt. R.I.B.
The ZAR 65 is also fantastic wen You ask the entire maximum possible place to enjoy the sun and the sea.
Two huge front and back sun beds, a comfortable front dinette with table, many many peaks and enough place for easy life on board.

ZAR 65 XL version with transom fit for single-engine with extra-long shaft

More Less

Product category: Inflatable Boats

ZAR 85 SL

The ZAR 85 SL is born as flagship of the Sport Luxury Line, wich already includes the ZAR 49 SL and the ZAR 59 SL. The project is developed from the consolidated structure of the ZAR 87 which hosts an internal bath cabin, where you can stand comfortably. The same hull is perfectly adapted for the sporting concept, in line with the Sport Luxury series. Even in this new ZAR 85 SL, there is space for a toilet under the console, that can also be transformed into a double bed.

The high performance together with a futuristic and eye-catching design of the deck, make the ZAR 85 SL trendy, ideal for lovers of style and, dare we say, the glamour. The sports-oriented and ergonomic design make the ZAR 85 SL perfectly suited to being a tender for a large yacht, or a primary use boat.

More Less

Product category: Inflatable Boats

ZAR 59 SL

Second-born of the Sport Luxury line, a new series, however unchanged, that brings together all of the winning features that have led ZAR to be the point of reference in the world of Rigid Inflatable Boats.
It still maintains the great qualities of habitability, comfort, design and the special quality of navigation due to the unique ZAR
hull design.
The design of this new series, while remaining on the track marked by all emblazoned ZARs, rushes towards rays of light, unexpected angles and cuts surfaces which create harmony
in the parallel difformity of the lines.
The ZAR 59 SPORT LUXURY: a medium / large boat to discover that move forward the concept of RIBs with attractive and innovative design and technology, top level features, high class finishing, and an enormous amount of attention to details, quality and construction.

More Less

Product category: Inflatable Boats

ZAR TENDER ZF0

The smallest among the ZAR Tenders line, which gave ZAR recognition as one of the leading companies in the luxury tender market.
All of the iconic elements such as the deep ‘V’ hull for great performance and comfort, the rigid bow for a more spacious interior, the enormous storage space, the quality materials selection and the innovative design have been uncompromised.
A key aspect of our design philosophy demands that these RIBS must be instantly recognizable as a ZAR.
The core values of our brand remain not only untouched, but enforced: Style, function, uncompromised, Italian.
Every feature of the tender line has been conceived for a fun, comfortable, practical and safe experience.
This ZF0 dares with new colors: black, and champagne for the cushons.

More Less

Product category: Inflatable Boats

ZAR mini ALU 15

ur ZAR miniTM ALU line is the ideal inflatable boat for people, who are looking for a reliable and safe foldable boat.  It is easy to assemble and can take an engine’s up to 40 hp.

The ZAR miniTM ALU line can easily pull water toys and tubes with the two installed D-rings on the transom.

With our specially designed two speed tubes installed under the main tube of ALU13, ALU14 and ALU15, you will enjoy a very unique fast and comfortable ride. It is real fun!

All foldable ALU inflatables from ZAR miniTM have a 5 layer reinforced high quality 1.100 dtex PVC material with a weight of 1.050g/m2  and a thickness of 0.9mm. All PVC seems of our ZAR miniTM tube chambers are welded*. To keep the weight down, we use a very strong but light constructed Aluminum floor that we manufacture in our production. High quality material’s paired with constant research & development are the key to success.
All foldable AIR inflatables from ZAR miniTM have a 5 layer reinforced high quality 1.100 dtex PVC material with a weight of 1.050g/m2  and a thickness of 0.9mm. All PVC seems of our ZAR miniTM tube chambers are welded*. High quality material’s paired with constant research & development are the key to success.

More Less

Product category: Inflatable Boats

ZAR mini PRO RIB 16SC

The ZARmini PRO RIB 16SC is the Mediterranean version pf the RIB 16 with a smeller console in order to leave space for a larger sunbed and related lokers.

Our ZAR miniTM RIB line has different sizes and versions. All boats can be equipped with a bow locker (“L”) and a flat double flooring (“D”). All boats starting from RIB11 have a bow locker and from RIB 12 a double flooring and a bow locker as standard features. Below these sizes (RIB8,9 & 10) you can choose what you need.

As optional equipment there are steering consoles and double seating (starting from RIB9 and only with double floor). You can also choose from a variety of sunroofs, bilge pumps, cushions and many more things. Please ask your ZAR miniTM dealer. He can serve you best.

The ZAR miniTM RIB line can easily pull water toys, waterski (from25hp) and tubes with the two installed D-rings on the transom.

Every ZAR miniTM has three lifting Davit lifting points. One in the bow and two on the transom. If your ZAR miniTM has a bow locker, you will have four lifting points.

Due to the very light aluminum hull it can go very fast and plan easily with a smaller engine. The hull will not face any problems of Osmoses or gel coat defects like a fiberglass hull. It will also last longer and not become heavier during use. The aluminum hull is being specially manufactured and powder coated to resist corrosion and saltwater. You will have a lot of fun with your ZAR miniTM RIB.

All RIB inflatables from ZAR miniTM until RIB14 have a 5 layer reinforced high quality 1.100 dtex PVC material with a weight of 1.050g/m2 and a thickness of 0.9mm.

All RIB inflatables from ZAR miniTM starting from RIB15 have a 5 layer reinforced high quality 1.100 dtex PVC material with a weight of 1.500g/m2  and a thickness of 1.2mm.

More Less

Product category: Inflatable Boats

ZAR mini RIB10HDL

Our ZAR miniTM RIB line has different sizes and versions. All boats can be equipped with a bow locker (“L”) and a flat double flooring (“D”). All boats starting from RIB11 have a bow locker and from RIB 12 a double flooring and a bow locker as standard features. Below these sizes (RIB8,9 & 10) you can choose what you need.

As optional equipment there are steering consoles and double seating (starting from RIB9 and only with double floor). You can also choose from a variety of sunroofs, bilge pumps, cushions and many more things. Please ask your ZAR miniTM dealer. He can serve you best.

The ZAR miniTM RIB line can easily pull water toys, waterski (from25hp) and tubes with the two installed D-rings on the transom.

Every ZAR miniTM has three lifting Davit lifting points. One in the bow and two on the transom. If your ZAR miniTM has a bow locker, you will have four lifting points.

Due to the very light aluminum hull it can go very fast and plan easily with a smaller engine. The hull will not face any problems of Osmoses or gel coat defects like a fiberglass hull. It will also last longer and not become heavier during use. The aluminum hull is being specially manufactured and powder coated to resist corrosion and saltwater. You will have a lot of fun with your ZAR miniTM RIB.

All RIB inflatables from ZAR miniTM until RIB14 have a 5 layer reinforced high quality 1.100 dtex PVC material with a weight of 1.050g/m2 and a thickness of 0.9mm.

All RIB inflatables from ZAR miniTM starting from RIB15 have a 5 layer reinforced high quality 1.100 dtex PVC material with a weight of 1.500g/m2  and a thickness of 1.2mm.

More Less

Product category: Inflatable Boats

ZAR mini AIR 7

Our ZAR mini AIR line is the ideal inflatable boat for people, who are looking for a reliable and small foldable boat.  It is very easy to assemble and easily stowed away.

The ZAR mini AIR line was designed as a tender for motor and sailing yacht’s. It is your ideal dinghy for everyday use.

The high pressure floor, made in the “drop-stich” processing, can be inflated until 0.8 bar. Together with the air keel, that can be inflated until 0.35 bar, the small ZAR miniTM AIR gets very rigid and planning is easy.

We have chosen the flat double flooring with air keel, because it has the advantage that in comparison to a  V-floor you can still drive, if your high pressure flooring has a leakage.

All foldable AIR inflatables from ZAR miniTM have a 5 layer reinforced high quality 1.100 dtex PVC material with a weight of 1.050g/m2  and a thickness of 0.9mm. All PVC seems of our ZAR miniTM tube chambers are welded*. High quality material’s paired with constant research & development are the key to success.

All boats feature an overpressure valve, as standard equipment, that will protect your tube when inflated properly.

Every single ZAR miniTM inflatable boat passes a very strict quality control, before we deliver it to our valued customers. Just in case a mistake passes the quality control, you will be protected by our limited 2 years warranty after registering your boat with us.

With our large standard equipment and our modern Italian Design with an extra wide bow, the ZAR miniTM inflatables are one of a kind.

The ZAR miniTM AIR line is ideal for small storages in yacht or car.

More Less

Product category: Inflatable Boats

ZARmini FUN 6

Our ZAR miniTM FUN line is the ideal inflatable boat for people, who are looking for a reliable but very small foldable boat.  It is very easy to assemble and easily stowed away.

The ZAR miniTM FUN line was designed as a very light tender for small motor and sailing yacht’s. It is your ideal dinghy.

The wooden slatted deck can be rolled up very fast. Everything is very light and easy in use. Practically you only need to inflate and deflate the tubes.

All foldable FUN inflatables from ZAR miniTM have a 5 layer reinforced high quality 1.100 dtex PVC material with a weight of 1.050g/m2  and a thickness of 0.9mm. All PVC seems of our ZAR miniTM tube chambers are welded*. High quality material’s paired with constant research & development are the key to success.

All boats feature an overpressure valve, as standard equipment, that will protect your tube when inflated properly.

Every single ZAR miniTM inflatable boat passes a very strict quality control, before we deliver it to our valued customers. Just in case a mistake passes the quality control, you will be protected by our limited 2 years warranty after registering your boat with us.

With our large standard equipment and our modern Italian Design with an extra wide bow, the ZAR miniTM inflatables are one of a kind.

The ZAR miniTM FUN line is ideal for very small storages in yacht or car and for short distances.

More Less

Product category: Inflatable Boats

ZAR 53 Classic

It is the ZAR of records: (comfortable 8 front running seats, a double double bed, 8 peaks to stow goods and a range of unique combinations seats/sun bathing bed/bed/table. This boat has revolutionised the concept of the rubber dinghies, in only 5.35 meters it withholds all the innovations introduced by “ZAR project”. Ideal for the family, that can enjoy wonderful autonomous nautical camping days (and nights); ZAR 53 is excellent for all purposes. It bears high-rank motors (140 HP) and offers remarkable performance, or moderate ones (70 HP) without disadvantages for pleasant sailing.
It transports 10 persons, it has about 130 litres of fuel capacity and about 60 litres of water capacity under the walk fl oor without diminishing the passengers and peaks space. Everything has been planned and built for maximum comfort.
The hull is deep and long as much as the one of many bigger boats, it offers soft sailing on the waves, stable tacking and agility, all qualities that are unique in its category (and in the ones above). The line elegance and the practical design make ZAR 53 a unique rubber boat all over the world.

Complete with VTR two-seater drive console with front seat, peak under driver's seat, rudder and handrail of stainless steel, single cable steering, windshield, 2 separate indoor compartments, waterproof doors, anatomic driver's seat for two permitting driving in a semi-seated position; horizontally pivoted backrest and cushion for driver's seat; stainless steel ladder with dashboard on VTR; 4 bollards and 4 handrails made of stainless steel; stainless steel anchor winch nose; 3 gas springs for afterpeak and forepeak covers; prow cushion, stern cushion, stern headrest cushion, padded stern backrest, repair kit, inflation pump, pressure gauge, paddle oars. (All cushions are made of closed cell expanded polyurethane.)

More Less

Company news

Date

Topic

Download

Jan 13, 2017

Press Release

ZAR Formenti is glad to share with you the Press Release for the coming Boot Fair in Dusseldorf. For any info about our new boats have a look over our document.

More Less

About us

Company details

Founded in 1979, the Formenti boatyard has a long tradition and meticulous craftsmanship in manufacturing infl atable rubber boats.
Today the ZAR range of boats by Formenti is sold in all major European markets.
The company growth and the success of its product are the result of a precise strategy focused on quality rather than quantity, investments in R & D, the use of the best aterials, advanced technology and a modern, well-organized production facility. All workplaces are air-conditioned.
Developed and improved over the years, the company’s quality system was awarded ISO 9002 certifi cation by the Italian Mercantile Registry.

The most advanced IT together with a powerful, refi ned 3D software have been introduced in the years 2000. Today, the entire range of prototypes, of the moulds, of full size and on scale models is produced by CNC (computer numerical control) machines, which guarantee the sharpest precision.

Future is already there at ZAR-FORMENTI thanks to the research and development of cutting edge, nvironmental-friendly materials and production practices.

More Less